Bioprocess and fermentation monitoring

Bioprocess and Fermentation Monitoring: How to Assess Real-Time Analytics for Your Process

admin 11 min read
Bioprocess and Fermentation Monitoring: How to Assess Real-Time Analytics for Your Process

What bioprocess monitoring is meant to establish

Bioprocess and fermentation monitoring uses timely measurements to understand process behavior and track variables that matter to product and batch decisions. Process Analytical Technology (PAT) is an approach for designing, analyzing, and controlling manufacturing processes through timely measurements of critical process parameters. In a bioprocess, those measurements may include pH, dissolved oxygen, biomass, substrates, metabolites, and products.

Your first question is therefore not which instrument to buy. It is what you need to know during the run, when you need to know it, and what qualified decision the result may support.

UV-Vis monitoring commonly uses optical density or light scattering to measure cell concentration, and wavelengths between 350 and 400 nm have been reported as useful for differentiating viable and dead microbial cells. In one reported lovastatin fermentation-broth study, dual-wavelength UV-Vis had detection limits of 0.320 μg/mL in the standard solution and 0.490 μg/mL in the fermentation broth, with a quantification limit of 3.955 μg/mL for the broth sample.

A synthetic co-culture fermentation provides a different kind of warning. In that fermentation, small dissolved-oxygen changes could drive undesired products: deficient dissolved oxygen resulted in irreversible glycerol production, while excess dissolved oxygen resulted in acetoin rather than 2,3-BDO. The example does not establish a universal operating setting; it shows why the variables linked to your process outcome need to be identified before you interpret a signal.

Connect the result to a decision that matters during the run

Bioprocess analytical monitoring can support batch, fed-batch, perfusion, and continuous processes through off-line, at-line, on-line, or in-line measurements. The appropriate approach depends on the process decision, required response time, sampling conditions, and whether the measurement can be qualified for its intended use. PAT measurement planning should also establish whether the objective is routine monitoring, fault detection, classification, or end-of-process detection.

Before comparing measurement modes, define these points:

  • Process state: Identify the batch phase, feed stage, residence-time window, or transition that matters.
  • Measured variables: Name each substrate, product, metabolite, biomass measure, process parameter, or quality-related variable you need to observe.
  • Decision timing: State whether the result supports a trend review, an investigation, an endpoint assessment, or a possible operating response.
  • Measurement objective: Decide whether you need a direct assay, a model-derived estimate, an alert, or a classification.
  • Operating context: Record the sampling conditions and process features that could affect representativeness.

This sequence prevents a fast signal from being treated as useful simply because it arrives quickly. The signal must answer a defined process question.

An infographic checklist for defining a process monitoring question. It lists process state, measured variables, decision timing, measurement objective, and operating context.
A fast signal is useful only when it answers a defined process question.

Compare visibility by how the sample reaches the measurement

Measurement access determines how closely the result follows a changing process. Timely information about biomass, substrates, metabolites, products, and nutrients can help support effective control decisions, but each access mode changes the relationship between the process, the sample, and the reported result.

Access mode How the measurement is obtained Reported timing or visibility Practical boundary
In-line A sensor measures inside the vessel or process stream without sample removal. Continuous or frequent observation may be possible, depending on the configuration. Sensor position, process interface, fouling, and qualification remain part of the measurement problem.
On-line A sample moves through a bypass stream and may return to the process. Measurements can be repeated through the bypass, with timing dependent on the method. The bypass and sample-conditioning path must represent the process and fit the equipment.
At-line A removed sample is analyzed near the process. At-line measurement is reported as taking 15-60 minutes. The delay and sample handling may limit its use for rapidly changing cultures.
Off-line A sample is removed, transported, and analyzed in a separate laboratory. Off-line measurement is reported as taking 2-6 hours. It remains useful for laboratory analysis and reference measurements, but the delay limits observation frequency.

The reported timing is 15-60 minutes for at-line measurement and 2-6 hours for off-line measurement, while actual timing depends on the method and process.

Manual sampling can be time-consuming, can miss changes between samples, and can create contamination risk for a batch. Offline analysis in traditional fermentation settings can delay results by several hours to days, making it difficult to capture dynamic fermentation changes in real time.

Manual beer-fermentation sampling can take 10-15 minutes per sample, is not continuous, may miss optimal completion, and poses a contamination risk to the batch. The same source describes a Micro Motion Fork Density Meter that enables continuous fermentation measurement and reports ±1 kg/m³ accuracy or ±0.2 °Plato concentration accuracy. Those are claims about that cited instrument and application, not a general performance value for every monitoring system.

A separate bioprocess study reported a turbidity-to-total-cell-concentration correlation of R2 ≥ 0.97 and a Raman PLS model with RMSE ≤ 13.82 and R2 ≥ 0.92 against offline viable-cell measurements. These figures describe the reported study conditions; they do not remove the need to examine your sampling path and reference method.

A StatRow infographic comparing reported measurement timing. At-line measurement is shown as 15-60 minutes, and off-line measurement as 2-6 hours.
Sample access changes how quickly a result can inform a changing process.

Separate the spectrum from what the process team needs to know

A mid-infrared instrument measures infrared absorption at specific frequencies and produces a spectrum representing absorbance across a range of infrared frequencies. The spectrum is the measured pattern; it is not automatically a concentration, endpoint, or process decision.

A mid-infrared spectrometer can support real-time, in situ or ex situ monitoring of multiple analytes in complex fermentation fluids, but deployment limitations remain. The practical question is whether the sample reaches the measurement in a controlled and representative way, and whether the resulting spectral information can be interpreted for your process.

Spectroscopy combined with chemometric techniques can generate soft sensors that estimate process variables from process and measurement models. Variables that are not directly accessible in situ, such as biomass and substrate concentration, can therefore be estimated from spectral or other measurement data when the model connects those data to suitable reference results.

The estimate belongs to the model’s demonstrated process scope. A spectrum may remain useful for trend monitoring even when a quantitative concentration estimate is not ready for an operating decision. Keep those uses separate in your requirements and review plan.

Some spectroscopic techniques are non-selective in complex solutions or suspensions, so multiple compounds may contribute multiple bands or peaks to the measured spectrum. Chemometric interpretation therefore depends on calibration data that represent the relevant matrix and process variation, not on assigning a single spectral feature to one analyte. A technical review should ask how the model distinguishes overlapping contributions before treating an estimate as quantitative evidence.

Choose measurement access before qualifying a concentration estimate

A quantitative estimate needs an evidence chain from the process question to the reference result. A practical sequence is:

  1. Define the measurement. Specify the quantity, units, sampling context, process states, and intended decision.
  2. Design calibration data. Build the calibration set across the expected concentration range, including the extremes, and represent the intended process, chemistry, and operating conditions.
  3. Collect reference pairs. Link each spectrum to a reference result whose measurement behavior is understood.
  4. Build and cross-validate the model. Examine how the multivariate relationship behaves during development.
  5. Validate independently. Use held-out batches or runs that were not used for calibration or model development.
  6. Deploy within the tested scope. Treat predicted concentrations as estimates tied to the demonstrated process conditions.
  7. Monitor and reassess. Reassess and revalidate the model when feedstock, temperature, product specifications, or other defined process conditions change.

Architecture selection is a separate decision from model qualification. An in-line arrangement is worth investigating when the process requires frequent observation and a representative process interface can be maintained without sample removal. An on-line bypass arrangement is worth investigating when controlled sample handling or conditioning is needed and the bypass can represent the process. At-line measurement can fit a workflow in which a nearby result arrives quickly enough for the decision, whereas off-line measurement is better positioned for reference analysis or validation when its longer delay is acceptable. These are fit criteria, not universal suitability rules; the selected arrangement still requires site-specific qualification.

Reference-method quality sets a hard boundary. Predicted values cannot be more accurate than the reference method used for training, and the reference method’s reproducibility determines the model’s accuracy floor. A model cannot remove material variability in the assay that supplied its training targets.

A published NIR calibration-development approach reported reducing calibration modeling time and cost by up to 50% relative to its comparison approach by reducing the number of samples required. That result describes the reported approach, not a general reduction for every calibration project.

One dual-wavelength UV-Vis method reported detection limits of 0.320 μg/mL in standard solution and 0.490 μg/mL in fermentation broth, with a broth-sample quantification limit of 3.955 μg/mL. Detection and quantification limits are method-specific measurements; they should not be treated as a general threshold for another analyte, matrix, or process.

A StatRow infographic showing reported limits for one dual-wavelength UV-Vis method. It lists 0.320 milligrams in standard solution, 0.490 milligrams in fermentation broth, and 3.955 milligrams as the broth-sample quantification limit.
Detection and quantification limits must stay tied to the method and matrix that produced them.

Check whether the measurement represents the real process

Measurement representativity is influenced by sensor characteristics, positioning, and process-sampling-interface design. A sample may not represent the process when sampling location, mixing, aggregates, settling, carryover, matrix effects, or sample conditioning are not considered.

Describe the physical process before you judge the result. Characterize flow regime, mixing dynamics, particle-size distribution, and potential sources of heterogeneity. Then record temperature, pressure, solids, sample conditioning, sampling path, and any changes that could alter the relationship between the measured material and the process stream.

Bioprocess models also require evaluation of predictiveness and uncertainty, and no single validation approach fits every model or bioprocess.

A sourdough fermentation study reported gas-sensor-array calibration models with percentage RMSE from 1.4% to 12% for pH and from 2.7% to 9.3% for total titratable acidity. Those ranges describe the reported pH and TTA models in that study, not a performance expectation for another fermentation, sensor array, or model.

Use examples like this to identify which variable was modeled, which reference measurement was used, and which process conditions were represented. Do not transfer the reported error range to your process without comparable validation.

Checklist infographic of five inputs that shape measurement representativity: sampling location, mixing and flow, material heterogeneity, sample interface, and model evidence. The items show what to examine before transferring a result to the real process.
A representative result depends on the whole sampling and modeling path, not the sensor alone.

Set the response before the signal arrives

A monitoring result should enter a defined review path before it can influence operation. Define the response, limits, and review path before allowing a measurement to influence operation.

When a result is missing or inconsistent, a spectral residual rises, or process variability is unexplained, investigate the data path rather than automatically changing controls or making a disposition decision. Review the following in sequence:

  • Confirm that the sample or sensor saw a representative process condition.
  • Check sample handling, conditioning, carryover, and instrument status.
  • Separate the spectrum from the model-derived concentration estimate.
  • Compare the estimate with the reference method and examine the reference result.
  • Check whether the process remains inside the model’s demonstrated scope.
  • Escalate the interpretation through the qualified review path before an operating response.

Seek qualified evaluation when the consequence is consequential

Qualified site review should remain part of the decision when monitoring could affect safety, quality, containment, or plant operation.

The same boundary applies when a measurement may influence a feed, harvest, release, containment, or other critical operating decision. Define who reviews the result, which evidence they need, and what action remains prohibited until that review is complete.

Prepare a scoped technical discussion or sample test

A process brief gives you a practical way to decide whether a real-time monitoring approach deserves technical investigation. Prepare the following information before requesting a discussion or sample-testing assessment:

  • Process question: State what you need to know and which decision the result may support.
  • Stream and analytes: Describe the stream composition and name the target substrate, product, metabolite, biomass measure, or other variable.
  • Concentration range: Give the expected range, including extremes where they are known.
  • Required accuracy: State the accuracy or uncertainty requirement in relation to the decision, not as an isolated instrument specification.
  • Operating conditions: Record temperature, pressure, solids, flow or mixing context, and relevant process states.
  • Samples: Identify representative samples and explain how they were collected and stored.
  • Sampling path: Describe the proposed in-line, on-line, at-line, or off-line route and any conditioning steps.
  • Reference method: Name the method used to establish reference results and describe its measurement behavior.
  • Intended use: Say whether the output is for trend monitoring, endpoint assessment, model input, fault investigation, or an operating response.

This information lets a technical discussion focus on measurement fit rather than a general application label. It also makes the limits of a sample test explicit: a laboratory result supports the conditions tested, not every future process condition.

Prepare a process brief for a qualified next discussion

Real-time analytics deserves investigation when a defined process question, required decision timing, representative measurement path, suitable reference method, and tested model scope align. Prepare the process brief before asking a signal to support an operating or quality decision. A qualified professional should decide individual suitability when safety, quality, containment, or plant operation could be affected. We can discuss the defined process question and whether sample testing is an appropriate technical next step.


What should you clarify before discussing bioprocess monitoring?

Can bioprocess and fermentation monitoring replace offline sampling?

Usually, it should complement rather than automatically replace offline or reference methods. Real-time signals can reveal trends and changing process behavior, while offline results may remain necessary for reference measurements, model verification, validation, and consequential quality decisions. The appropriate balance depends on the intended use, measurement qualification, and process conditions.

What makes a fermentation monitoring sample representative?

Representativeness depends on sampling location, mixing, flow behavior, aggregates, settling, carryover, matrix effects, sample conditioning, and sensor or interface design. Assess these factors alongside temperature, pressure, solids, and process state before treating a result as evidence of the whole process.

When does a chemometric model for fermentation monitoring need reassessment?

Reassess the model when feedstock, temperature, product specifications, or other defined process conditions change. New conditions may fall outside the calibration and validation evidence, so independent testing and, where relevant, revalidation should occur before extending the model’s use.

What should happen when a real-time monitoring result conflicts with expected process behavior?

Do not automatically change critical operating conditions or make a disposition decision. First investigate the data path, including representativeness, sample handling, instrument status, model scope, spectral residuals, and comparison with the reference method. Escalate promptly to the responsible process, quality, or safety authority when safety, quality, containment, or plant operation could be affected.


Next step

Have a question for Paeonia Innovations?

Get in touch