mid infrared spectroscopy and challenges in industrial environment

Industrial Mid-Infrared Spectroscopy: How to Assess Measurement Challenges

admin 12 min read
Industrial Mid-Infrared Spectroscopy: How to Assess Measurement Challenges

Industrial conditions determine whether the spectrum remains useful

Industrial mid-infrared spectroscopy can serve selected measurements, but feasibility depends on whether useful spectral information and quantitative interpretation can be maintained in your actual sample matrix and operating conditions. A chapter on mid-infrared absorption identifies an advantage for measuring trace concentrations of a few gases whose transitions are very weak in the near-infrared. A separate review describes high-fidelity online near- and mid-infrared measurements as highly challenging in dynamic industrial environments. Those points belong together: a measurement opportunity does not establish that a particular process can be measured successfully.

The practical question is not simply whether a target has a usable infrared signal. You also need to ask what else is present, which industrial disturbances could affect the spectrum, and whether the way you interpret the data remains appropriate under those conditions. The sections below connect those disturbance categories to questions you can investigate before selecting or deploying an approach.

One useful distinction is between an enabling source and an established process measurement. The chapter attributes industrial interest partly to the availability of industrial-grade room-temperature intraband and quantum cascade lasers, describes those lasers as repeatable in performance, and says these sources, together with near-infrared lasers, have opened the infrared spectral band to industrial applications. That context explains why more measurements are practical to investigate; it does not establish that the full measurement is unaffected by matrix effects or industrial disturbances. Keep source availability and performance of a measurement under its intended conditions as separate questions.

At Paeonia Innovations, we offer the OrionIR® mid-IR spectrometer, which provides one spectrum every second across 900–3500 cm⁻¹ through aqueous, strongly absorbing, and low-concentration streams. That describes a stated instrument capability; it does not establish suitability or measurement performance for your particular application.

A one-spectrum-per-second specification is a stated acquisition cadence, not by itself evidence that a process change will be resolved for a particular use. Compare that interval with the changes your measurement is intended to follow, then investigate whether the relevant results are captured under your conditions; the specification alone does not establish response time, accuracy, or suitability.

Gas absorption and liquid-stream measurements pose different questions

Gas-phase absorption and liquid-stream monitoring are distinct measurement settings, so evidence from one should not be treated as proof of fit in the other. The chapter describes tunable laser absorption spectroscopy as having widespread applications in real-time, in-situ, non-invasive gas sensing. It also identifies a mid-infrared absorption advantage for trace concentrations of a few gases with very weak near-infrared transitions. That advantage is specific to those gases; it does not mean every target gas or industrial measurement presents the same analytical question.

Method labels also matter when you compare the gas examples. The chapter describes tunable laser absorption spectroscopy for real-time, in-situ, non-invasive gas sensing; the NIST passage instead describes FT-IR absorption with multivariate analysis and published reference spectra for quantitative gas analysis. These are different method descriptions and purposes, not a head-to-head test. A shared infrared region or gas-phase target does not show that the methods use the same measurement arrangement or interpretation. Note the method and the result being evaluated when deciding whether an example is relevant to your own question.

Mid-infrared spectroscopy using attenuated total reflection (ATR) can be used to follow reactions in liquid process streams and reaction vessels. Treat that as a description of an application, not a general performance guarantee. Your assessment should identify the measurement mode, the material being measured, and the result you need. A gas concentration question and a reaction-following question call for different evidence about the sample and measurement arrangement.

Infographic comparing gas-stream and liquid-stream measurement settings. It shows gas sensing and concentration questions alongside liquid reaction-following with mid-infrared ATR and changing measurements.
Match the evidence to the sample and measurement mode you need.

Moisture and multiple components complicate quantitative interpretation

Moisture and multiple components make quantitative interpretation a central feasibility issue for complex process matrices. A review of online process spectroscopy describes real-time quantitative analysis of complex matrices, including moisture and multiple components, as a critical bottleneck in Process Analytical Chemistry. The same review says that achieving high-fidelity online measurements in dynamic industrial environments remains highly challenging. The implication for your assessment is practical: characterize the material that will actually be measured, not only the target analyte in isolation.

For the intended measurement, list the target, the other components you expect to be present, and any changes in composition that form part of the operating conditions. Ask whether moisture or another component could affect the spectral information needed for your quantitative interpretation. Possible spectral overlap is worth treating as a question to investigate, not as an established problem in every mixture. Record what is known about the matrix and what still needs to be tested.

The difference between recognizing a pattern and estimating a quantity matters here. Your task may be to follow a change or to produce a quantitative value; those are not interchangeable requirements. State the intended output before judging whether a spectrum is useful, and ask how the matrix present during measurement relates to the conditions used to interpret it. If those conditions differ, identify that gap for investigation instead of assuming a quantitative interpretation will transfer unchanged.

Separate components that remain stable from those that may vary across the operating conditions you need to represent. For each expected variation, note whether it changes the sample composition relevant to your measurement and whether your planned assessment includes that condition. This gives you a specific matrix question to resolve instead of treating “the sample” as a single fixed composition. If you do not yet know which variations matter, record that uncertainty as part of the feasibility work.

Window pollution and source fluctuations can distort online spectra

Detector-window pollution and light-source drive-voltage fluctuations are two industrial disturbances identified in a review of online process spectroscopy. The review groups them with matrix effects and other industrial interferences, and reports that such disturbances often cause significant baseline drift and nonlinear spectral distortion. These are not merely abstract instrument concerns: they are specific disturbance categories to include when you describe the conditions under which an online measurement would operate.

Baseline drift and nonlinear distortion are different descriptions of changes in the measured spectrum. The review identifies both as possible consequences of matrix effects and industrial multi-stress interferences. For your feasibility investigation, ask whether window pollution or source-voltage fluctuation is plausible in the intended setting, how either condition would be noticed, and whether your assessment includes measurements made under the relevant disturbance conditions. These questions identify what needs attention; they do not assume that a particular disturbance will occur at your site. Because the review names matrix effects and industrial stresses as contributors to these changes, drift or distortion alone does not identify its cause. During an assessment, record sample composition and relevant window and source conditions alongside each spectral observation. If composition and instrument conditions change together, treat the result as ambiguous rather than attributing it to the target or to one disturbance; compare conditions in a way that lets the possible contributors be examined separately.

Infographic showing detector-window pollution and source-voltage fluctuation converging on spectral behavior. The outcomes shown are baseline drift and nonlinear spectral distortion.
Connect each disturbance under consideration to the spectral change you will examine.

Interference can challenge both optical limits and calibration models

Spectral interference can challenge the physical optical limits of a measurement as well as a traditional linear calibration model. The review makes both points, which means that feasibility should not be reduced to a single question about data processing. Ask separately whether the physical measurement can provide useful information under the conditions of interest and whether the method used to interpret that information is appropriate for the matrix and operating range.

Representative test conditions make quantitative evidence interpretable

Quantitative evidence is easier to interpret when the test conditions and the intended application are clearly defined. A NIST passage describes FT-IR absorption spectroscopy using multivariate analysis and published reference spectra as a common tool for quantitative gas analysis. The passage identifies the use of reference spectra rather than consumable gas-cylinder standards as an advantage of the described approach. This is a bounded example of a method and its stated context, not evidence that every process can use the same approach.

For your investigation, that points to two useful questions: are the measurement conditions and analysis procedures stated clearly enough for someone else to understand the result, and are the associated uncertainties recorded? These records do not remove differences between test conditions and your process.

That distinction matters when reading claims about standards. In the described FT-IR approach, published reference spectra provide the comparison basis in place of consumable gas-cylinder standards; the passage does not claim that no reference information or defined procedure is needed. When reviewing quantitative evidence, identify which reference spectra and protocol support the result and treat the uncertainty as part of the evidence, rather than reading comparability as a guarantee that conditions elsewhere match. If a report omits protocol, reference-spectrum, or uncertainty information, identify that as a limit on what the evidence permits you to compare, not as proof that the measurement failed.

The described NIST work examined FT-IR analysis of hazardous-material vapor streams at AEGL under test conditions defined in ASTM E2885-13 and E2933-13. Keep that example attached to its stated purpose and test conditions. It can inform how you think about defining a quantitative gas-analysis investigation, but it does not establish performance for a different analyte, matrix, or industrial process. When you review a result, note which parts of its conditions match your intended use and which do not.

Compare infrared methods against the analyte and measurement conditions

Near-infrared and mid-infrared should be assessed against the analytical problem, rather than ranked in the abstract. The mid-infrared trace-gas advantage described in the chapter applies to a few gases with very weak near-infrared transitions. A comparison of infrared methods advises engineers to assess the problem objectively rather than deciding in advance to use only near-infrared or only mid-infrared. Together, those points support a conditional choice: start with the analyte and required measurement, then ask which approach has relevant evidence for that use.

For your application, consider what you need to measure, the concentration range that matters, whether the target has the relevant spectral behavior, and whether the measurement is for a gas or a liquid process stream. Then include the matrix and operating conditions in the comparison. These are screening questions, not proof that one infrared region will meet your requirements. If the evidence does not address a condition important to your use, make that a test question rather than filling the gap with a general preference.

ATR mid-infrared spectroscopy is described for following reactions in liquid process streams and reaction vessels; that example is relevant only when the measurement setting resembles yours. It does not settle a gas-detection question or determine how a different sample will behave. Keep the mode, sample type, and desired output explicit when you compare options. Where the application differs, investigate the difference directly.

Turn each disturbance into a question to investigate

A feasibility investigation can be framed around observable questions about relevant disturbances. The review identifies matrix effects, detector-window pollution, and source-drive-voltage fluctuations as challenges, and says the resulting interference can challenge optical limits and traditional linear calibration models. NIST’s discussion of protocols and reference spectra offers a separate prompt: define how you will describe conditions and document uncertainty.

  1. Define the measurement. Name the analyte or target, the result you need, and whether the measurement concerns a gas stream or a liquid process stream. State the concentration range or other requirement that matters to your use. If the target and intended output are not clear, narrow the question before comparing approaches. The described mid-infrared trace-gas advantage applies to a few gases with very weak near-infrared transitions, not to every gas or measurement.

  2. Describe the matrix. List moisture and the other components you expect to be present, along with any composition changes that belong to the intended operating conditions. Ask whether another component or possible spectral overlap could complicate the quantitative interpretation you need. Mark uncertainties as questions for investigation rather than assuming they are either present or irrelevant. The review identifies complex matrices, including moisture and multiple components, as a bottleneck for real-time quantitative analysis.

  3. Specify the physical measurement arrangement. Record how the sample is presented to the measurement, what interfaces contact the stream, and how the optical path is defined for your setup. Ask which parts of that arrangement are represented in your available test evidence. These prompts help distinguish a test of the analytical question from a test that uses a different sample interface or path. Treat any difference as something to examine under conditions that matter to your use.

  4. Name likely process disturbances. Consider whether window pollution, source-drive-voltage fluctuations, or other relevant industrial stresses could be present during the measurement. Ask what spectral behavior you would inspect for baseline drift or nonlinear distortion and how those observations relate to the result you need. If your assessment assumes uninterrupted operation, write down the continuous-operation conditions that assumption represents. The review identifies window pollution and source-voltage fluctuations as industrial interferences and links multi-stress interference with baseline drift and nonlinear spectral distortion.

  5. Examine measurement and interpretation separately. Ask whether the physical measurement can provide useful information under the conditions you intend to test, then ask whether the quantitative interpretation is appropriate for the matrix and conditions represented. The review notes challenges to both physical optical limits and traditional linear calibration models. Do not treat an adjustment to one side of the problem as evidence that the other side has been resolved.

  6. Make the test conditions legible. State the protocol, reference spectra where applicable, conditions represented, and how you will record uncertainty. The NIST passage says standard protocols and reference spectra can support cross-laboratory comparison and documentation of associated uncertainties. Compare the proposed test conditions with your intended application and list each meaningful mismatch. That list defines what your next assessment needs to address; it does not establish a result in advance.

Checklist infographic of feasibility questions: define the measurement, describe the matrix, specify the arrangement, name process disturbances, examine measurement and interpretation separately, and make conditions legible.
Use these prompts to identify what the feasibility assessment still needs to learn.

Make the next assessment specific to the application and site

Industrial mid-infrared feasibility turns on the relationship between the target measurement, the actual matrix, the disturbances that may affect the spectrum, and the conditions used to interpret the result. The available examples support investigating those factors; they do not guarantee accuracy or suitability for an unspecified application. Your next assessment should name the unknowns that matter most and the conditions needed to examine them.

For work involving sites in North America, South America, Europe, or Asia, record each site’s continuous-operation pattern, classified-area conditions, and applicable regulatory environment separately. Check the requirements that apply at each location rather than assuming conditions are equivalent. A qualified professional should determine suitability for your specific measurement. End your assessment with a short list of the open questions, the conditions that matter to each, and what you need to investigate next.


What should be established before assessing an industrial mid-IR measurement?

What are the main challenges of mid-infrared spectroscopy in industrial environments?

Complex sample matrices, including moisture and multiple components, can complicate quantitative interpretation. Industrial disturbances such as detector-window pollution and light-source drive-voltage fluctuations can contribute to baseline drift and nonlinear spectral distortion. Feasibility also depends on whether the physical measurement and the interpretation method remain appropriate under the conditions being assessed.

How can you assess whether mid-infrared spectroscopy is suitable for a process measurement?

Define the target, required output, sample type, and conditions the measurement must represent. Then assess the matrix, possible disturbances, physical measurement arrangement, and interpretation method separately. Compare available evidence with your intended use and record conditions or uncertainties that remain untested; a result from a different analyte, matrix, or process does not establish suitability for yours.

How should gas-phase and liquid-stream measurements be evaluated differently?

Treat them as distinct measurement settings. For gas sensing, identify the target gas and the concentration question; the described mid-infrared advantage applies to a few gases with very weak near-infrared transitions. For liquid-stream monitoring, specify the sample and measurement mode, such as ATR when following a reaction. Evidence for one setting does not establish fit in the other.

How do moisture and multiple components affect industrial infrared measurements?

They can make real-time quantitative interpretation challenging because the measured matrix is more complex than the target alone. List the expected components and composition changes, then investigate whether moisture or another component affects the spectral information needed for your result. Treat possible spectral overlap as a question to test for your application, not as an assumption about every mixture.

What should a quantitative gas-analysis test record?

State the target, measurement conditions, procedure, reference spectra where applicable, and how uncertainty is documented. Compare those conditions with the intended process and identify meaningful differences. Standard protocols and reference spectra can support comparison across laboratories and documentation of uncertainty, but they do not establish performance under untested conditions.


Next step

Have a question for Paeonia Innovations?

Get in touch